Weitere Marken von Sievert
Suche
On the list VESTEROL® MS 55HSP

VESTEROL® MS 55HSP

Multi-functional filler for universal use on concrete and masonry
CHARACTERISTICS
VESTEROL® MS 55HSP is a one-component mineral filler for fast repairs. Formulation and colour of the very low-stress. This polymer-modified mortar (PCC) make it especially suitable for rapid repair of concrete, since it replaces corrosion protection, primer coat and repair mortar.
  • corrosion resistant
  • low-stress
  • fast setting
  • easy to process
  • high-pressure resistant
  • high adhesive tensile strength
  • class R2 DIN 1504-3

INGREDIENTS
Standard cements, mineral aggregates, fillers, HS pozzolans.

    USE
    VESTEROL® MS 55HSP is suitable for universal outdoor and indoor repairs of wall, ceiling and floor surfaces. Extendable up to grain strength 0,3 mm for levelling surfaces and fixing spalled surfaces up to 50 mm.

    Areas of application:

    • indoor and outdoor areas
    • re-profiling and levelling
    • on concrete, plaster, masonry and floor pavement

    QUANTITY REQUIRED
    With 1 mm layer thickness1.25 kg/m2


      1) With +20 °C and 60 % relative air humidityPREPARATION OF THE SURFACE
      The surface must be clean, firm and free from adhesion-reducing particles such as dust, oil or friable parts. The adhesive tensile strength should be min. 1.5 N/mm2.

        APPLICATION
        1.Fill a clean mixing container with water. Use 3.2 litres for 20 kg of powder.
        2.Add VESTEROL® MS 55HSP and mix with a mechanical stirrer with approx. 400 rpm until a smooth paste is formed. Mixing time: 2-3 minutes
        3.Processing of the material takes place with a standard application tool such as a spatula or a steel float on dry or slightly damp surfaces within a processing time of approx. 45 minutes.
        4.To achieve optimal adhesion to the substrate, VESTEROL® MS 55HSP is integrated into the substrate as scratch coat using a smoother and sufficient pressure. Alternatively, VESTEROL® MS 55HSP is mixed to form an adhesive slurry and brushed intensively with a brush or wide brush. To achieve a slurry consistency: stir approx. 0.2 l water (2%) into the readily mixed sealing putty. Then the desired layer is constructed.
        5.Clean tools with water after use. After hardening the material can only be removed mechanically.

        IMPORTANT NOTES
        • Observe the processing temperature from +5 °C to +30 °C.
        • Setting material should neither be diluted with water nor mixed with fresh mortar.
        • Protect material against drying out too rapidly and unfavourable weather conditions. Avoid draft and direct solar radiation.
        • Adding more water leads to increased shrinkage and loss of hardness.
        • Observe (keep to) a mixing time of at least 2 minutes

        SAFETY PROVISIONS/RECOMMENDATIONS
        Contains cement; alkaline reaction with moisture/water. Please gather further information on safety during transport, storage and handling from the current material safety data sheet.

          DISPOSAL
          The local waste removal regulations must be observed.

            SPECIFICATIONS
            Packaging
            Container
            Form of delivery
            Shade of colour
            Processing temperature
            Fresh mortar density
            Processing time1)
            Adhesive tensile strength1)
            Pressure resistance1)
            After 24 hours
            After 3 days
            After 7 days
            Amount of water needed
            Storage            		paper sack
            20 kg
            36 sacks/pallet
            grey
            +5 °C to +30 °C
            1.5 kg/l
            approx. 45 minutes
            2.8 N/mm2

            10 N/mm2
            20 N/mm2
            25 N/mm2
            3.2 litres per 20 kg
            dry, 6 months