Weitere Marken von Sievert
Suche
do notatnika IMBERAL® Aquarol Winter 16D

IMBERAL® Aquarol Winter 16D

Special primer for structural waterproofing, up to -5 °C in winter
CHARACTERISTICS
IMBERAL® Aquarol Winter 16D is a red-pigmented primer with a chemical and physical action, specially matched to the stringent requirements of modern waterproofing technology.
Bonds the adhering dust (abrasion, cement and quartz dust) to the mineral structural surface.
Compacts structural surfaces through silicate bonding and forms a substrate that is capable of bearing loads, for the waterproofing to follow.
Reduces the absorbency of the substrate by hydrophobising of the surface zone and reduces the danger of water seepage of the waterproofing.
  • Water-repellent
  • Consolidating
  • Can be brushed, rolled and sprayed
  • Frost resistant up to -5 °C

INGREDIENTS
Organic and inorganic bonding agents, hydrophobising agents, wetting agents, pigment, freezing point reducers

    USE
    IMBERAL® Aquarol Winter 16D as a primer, specially for 1-component and 2-component bitumen thick coats, especially IMBERAL® 2K Winter 26B, as well as for traditional bitumen coats.

    Areas of application:

    • Dry and temporarily slightly moist surfaces
    • Absorbent mineral substrates
    • Horizontal and vertical surfaces

    QUANTITY REQUIRED
    Depending on absorbency
    of the substrate
    0.15 -0.25 kg/m2

      PREPARATION OF THE SURFACE
      The substrates must be ice-free, absorbent, firm, capable of bearing load and free of loose components.
      The substrate can be slightly moist.
      Clean the base projections. Remove sinter layers and impurities.

        APPLICATION
        DIN 18533 - Waterproofing of buildings
        DIN 1053 - Masonry
        Follow the directive for the design and planning of structural parts in contact with the ground with plastic-modified bitumen thick coating.
        1.IMBERAL® Aquarol Winter 16D should be applied on the substrate by brushing, rolling or injecting. On very dusty surfaces, application with a brush or broom is advisable, to get good integration of the dust.
        2.The thick layer waterproofing can already be applied once the primer has dried to a matt-moist state. Longer drying times do not have any adverse influence on the adhesion.
        3.Clean all processing equipment (injection) with water immediately after use.

        IMPORTANT NOTES
        • Protect neighbouring components from splatters and spray mist.
        • Maintain the processing temperature at -5 ℃ to +20 ℃.
        • When using hahne system products, attention must be paid to the respective processing temperature (data sheet).
        • Ensure freedom of the substrate from ice.
        • Do not process in direct sunlight.
        • Waterproofing below +5 °C does not fall under DIN 18533 and must be agreed upon separately.

        SAFETY PROVISIONS/RECOMMENDATIONS
        The product is alkali. All the usual hygiene procedures and precautionary measures for handling chemical products apply. If there is contact with the eyes, rinse them thoroughly with water and consult a doctor. Wear suitable work protection clothing.

          DISPOSAL
          The local waste removal regulations must be observed.

            SPECIFICATIONS
            Packaging
            Barrel
            Delivery form
            Processing temperature
            Control colouring
            Storage            		PE canisters
            20 kg
            24 barrels/pallet
            -5 ℃ to +20 ℃
            red
            not below -5 °C,
            12 months


              Produkty systemowe

              IMBERAL® 2K Winter 26B

              IMBERAL® 2K Winter 26B
              Grubowarstwowa masa bitumiczna do uszczelniania budowli, wersja zimowa do -5 °C

              IMBERAL® S100 90B

              IMBERAL® S100 90B
              Grubowarstwowa masa bitumiczna do uszczelniania budowli, wypełniona polistyrenem

              IMBERAL® 2K-D 20B

              IMBERAL® 2K-D 20B
              Grubowarstwowa masa bitumiczna do uszczelniania budowli, do bezpowietrznego natrysku

              IMBERAL® RSB 55Z

              IMBERAL® RSB 55Z
              Reaktywne, szybkie uszczelnienie budynków, elastyczne

              IMBERAL® Emuflex 20B

              IMBERAL® Emuflex 20B
              Bitumiczna powłoka malarska do uszczelniania budowli, bardzo elastyczna

              ÖKOPLAST® 1K 20B

              ÖKOPLAST® 1K 20B
              Grubowarstwowa masa bitumiczna do uszczelniania budowli, wypełniona polistyrenem

              ÖKOPLAST® 2K 20B

              ÖKOPLAST® 2K 20B
              Grubowarstwowa masa bitumiczna do uszczelniania budowli, zawierająca mikrowłókna

              INTRASIT® Poly-C1 54Z

              INTRASIT® Poly-C1 54Z
              Masa uszczelniająca do wykonywania uszczelnień w budownictwie lądowym nadziemnym i podziemnym, 1,5 - 5 mm