Weitere Marken von Sievert
Suche

DAKORIT® PUR1K 30P

Liquid plastic for seamless, elastic roof waterproofing
Applications:
  • Flat roofs in residential and industrial sectors
  • New build and restoration
  • Balconies, patios and terraces, covered walks in the HADALAN® system
  • Connections
  • For waterproofing roofs as well as balconies, loggias, and access walkways as per DIN 18531 (parts 1-5)

CHARACTERISTICS
DAKORIT® PUR1K 30P is a ready-to-use, roof sealant to be applied in liquid form. In combination with air humidity the coating dries into an elastic, vapour permeable, crack bridging and weather resistant roof skin.
  • Elastic
  • Walkable
  • High UV reflection
  • Weatherproof
  • Flexible at low temperatures
  • High solid content

INGREDIENTS
Polyurethane resin, aluminium flakes, solvents, additives, functional fillers

    USE
    DAKORIT® PUR1K 30P is applied in connection with a fleece reinforcing core for renovating and waterproofing flat roofs and in particular in adjoining areas. Suitable are almost all substrates such as: Bitumen sheeting, polymeric waterproofing sheets (after previous checking), concrete and screed as well as metals.

    QUANTITY REQUIRED
    Depending on exposure
    and substrate
    2.5 - 3.5 kg/m2


      1)At +20 °C and 60 % relative humidity.PREPARATION OF THE SURFACE
      The substrate must be dry, clean, have a capacity to bear load, and be clean and free of adhesion-reducing substances. Close larger cracks with DAKORIT® ES 40B. Heat-seal open overlap joints of bitumen sheeting or glue with DAKORIT® ES 40B. With foil roofs, check the compatibility beforehand. Pre-treat absorbent mineral substrates with DAKORIT® PUR1K 30P diluted with water of 2 : 1 with HADALAN® EPV 38L. Coating can take place after > 6 < 24 h. Alternatively, absorbent substrates may be primed with HADALAN® HV Uni 30DD. Here, the coating can be applied after an airing time of 20 minutes.

      The following sheeting material must be pre-treated with HADALAN® HV Uni 30DD before starting the coating work.

      EVALON
      VAE PLAN Type F
      Ammann Type CB-1,8 mm TPO-E-GV
      Saar Gummiwerke SG tan
      FDT Repanol fK


      Pre-treat the following sheeting material with DAKORIT® HG1 31H prior to the coating work.

      FDT Rhenofol CG
      Sika SLP-15 G
      FDT Rhepanol f
      Bauder FPO T-SV 15
      Bauder Thermofol D 15
      Sarnafil T
      RESITRIX SK, -SK P, -SK W, -MB, -CL
      Sintofoil TOP
      Firestone RubberGard

      On substrates not listed here, carry out a preliminary test. Please talk to our application technology department.

        APPLICATION
        Stir the product well before applying.
        1.Metal connection plates, cap flashings, penetrations and metal covers (iron, stainless steel, aluminium, copper, zinc) as well as various plastics should be primed with HADALAN® HV Uni 30DD bonding agent (see technical data sheet). The primed surface can then be coated after 20 minutes drying time.
        2.First spread about 1.5 kg/m2 of DAKORIT® PUR1K 30P with a rubber wiper, section by section, and then roll on evenly with a wool roller. Be sure to apply enough of the product so as to be able to properly bed in the non-woven fabric.
        3.Embed DAKORIT® DV110 89V, without creasing, into the fresh coating. Allow an overlap of at least 5 cm on the non-woven fabric lengths. To protect the fabric lengths from rain or condensation, roll a thin coat over them immediately after bedding them in.
        4.After the first coat has completely dried, apply the final coat, again using approx. 1.5 kg/m2 of DAKORIT® PUR1K 30P.


        By adding the reaction accelerator DAKORIT® Speed Up you can considerably speed up the setting process. Please refer to the relevant data sheet.IMPORTANT NOTES
        • Maintain a working temperature of +5 °C to +30 °C.
        • Protect DAKORIT® PUR1K 30P from rain while drying.
        • DAKORIT® PUR1K 30P is not suitable as sealing below extensive vegetation.
        • Do not apply the product during periods of high condensing humidity.
        • Clean tools after use with HADALAN® EPV 38L. Completely hardened material can only be removed mechanically.
        • Packs which have been reclosed can only be kept for a limited period of time.
        • DAKORIT® PUR1K 30P contains solvent which may cause odour nuisance during application and until it is completely dry.
        • Take appropriate precautionary measures.

        SAFETY PROVISIONS/RECOMMENDATIONS
        Detailed information on safe transport, storage and handling can be found in the current data sheet.

          DISPOSAL
          The local waste removal regulations must be observed.

            SPECIFICATIONS
            Packaging
            Pack
            Supplied
            Colour
            Density
            Working temperature
            Low temperature fracture
            (25 mm spike)
            Elongation at break in
            the system
            Tensile strength in the system
            Solids content
            Walkable1)
            Completely hardened 1)
            µ value
            sd value
            Storage
            Metal bucket
            17 kg / 7 kg / 3.5 kg
            30 / 72 / 96 packs/pal.
            silver grey
            1.5 kg/l
            +5 °C to +30 °C

            < -30 °C

            approx. 55 %
            approx. 6.5 N/mm2
            > 90 %
            after approx. 1 day
            after approx. 2 days
            2310
            3.97 m
            cool, 9 months


              Produkty systemowe