HADALAN^® FGM035 57M

USE
HADALAN^® FGM035 57M enables the production of easily-workable levelling coatings and epoxy resin screeds for indoor and outdoor use.

QUANTITY REQUIRED

Quantity required per litre of mortar with 5 % binder per l Fresh mortar density 1.75 kg/l with 10 % binder per l Fresh mortar density 1.90 kg/l

1.67 kg -FGM035 57M and 0.08 kg resin 1.73 kg -FGM035 57M and 0.17 kg resin

PREPARATION OF THE SURFACE
The substrates must be firm, bondable, free of frost, dust, dirt and other loose particles. Any rising damp or residual moisture must not exceed 4 %.
Non-bondable surfaces must be prepared by milling, sandblasting or similar. The tensile bond strength must not be lower than 1.5 N/mm², especially if the top surface is to be put under a high mechanical load.

APPLICATION

	1.	As a primer, the relevant resin is mixed and applied on the substrate. The mortar is applied on the fresh primer coat and compacted. If this is not possible, then the primer coat must be sprinkled with Quartz051 57M. The sand which remains on the surface must then be swept off. HADALAN® EBG 13E however can only be applied “fresh on fresh”: it is not possible to sprinkle with sand.
	2.	Mix HADALAN® MBH 12E or -EBG 13E with a slow-running power drill, re-pot and briefly stir through again. Then add HADALAN® FGM035 57M at the desired (correct) mixing ratio and mix in well with a sturdy rotary stirrer and a large basket-type stirrer. The mixing process is complete when the filler and the epoxy resin are homogeneously blended together Checking with a trowel during the process will help to determine this.
	3.	Epoxy resins react exothermically. Therefore you should use the mix quickly. The working time depends on the particular mixing ratio and the ambient temperatures. Depending on the conditions you have a working time of 20 to 45 minutes available to you.
	4.	After using HADALAN® MBH 12E tools can be cleaned (when still wet) with HADALAN® EPV 38L and after using HADALAN® EBG 13E (when still wet) with water. When they have dried off they can only be cleaned mechanically.

IMPORTANT NOTES

• Epoxy resins react exothermically. High temperatures accelerate the setting process, low temperatures slow it down.
• Only use complete bags, because if you only use parts of a bag the material can separate (become unmixed).
• When using screeds with a separation layer or an insulation layer please ask for assistance from our Technical Applications department (hahne Anwendungstechnik).
• The quantity of primer needed can vary considerably depending on the substrate and on the roughness of the surface.
• An additional pore-closing scratch coat must be carried out for subsequent coating systems.
• The minimum thickness of the mortar is twice the grain size.

SAFETY PROVISIONS/RECOMMENDATIONS
Please observe the standard hygiene and safety measures which apply when handling chemical products. Suitable protective clothing must be worn.

DISPOSAL
The local waste removal regulations must be observed.

SPECIFICATIONS

Packaging Quantity Delivery Form Colour / shade Strengths when used with HADALAN® MBH 12E or HADALAN® EG145 13E after 7 days 10 % MR 1:10 parts resin : filler 5 % MR 1:20 parts resin : filler 4 % MR 1:25 parts resin : filler Strengths when used with HADALAN® EPUni 12E after 7 days 10 % MR 1:10 parts resin : filler 5 % MR 1:20 parts resin : filler 4 % MR 1:25 parts resin : filler Strengths when used with HADALAN® EBG 13E after 7 days 5 % MR 1:20 parts resin : filler 4 % MR 1:25 parts resin : filler Bulk Density Storage

Paper bag 25 kg 40 bags/Pallet sand 50 N/mm2 30 N/mm2 22.5 N/mm2 40 N/mm2 24 N/mm2 18 N/mm2 15 N/mm2 12.5 N/mm2 1.6 kg/l dry, 24 months

• Safety data sheet
• Technical bulletin
• Brochure