Weitere Marken von Sievert
Jesteś tutaj:
- Produkte
- Masonry Repair Systems
- Sealing slurries
- INTRASIT® DS2 54Z
CHARACTERISTICS
INTRASIT® DS2 54Z is a combination of cement and mineral fillers that can be painted and spread with a trowel. It is free of efflorescence and has a hydrophobic effect.
Once hardened, the slurry is waterproof and offers excellent resistance to frost and heat.
INGREDIENTS
Standard cements, mineral aggregates, additives, synthetic dispersion powder, sealant
INTRASIT® DS2 54Z is a combination of cement and mineral fillers that can be painted and spread with a trowel. It is free of efflorescence and has a hydrophobic effect.
Once hardened, the slurry is waterproof and offers excellent resistance to frost and heat.
- Easy to apply
- Frost-resistant
- Waterproof
- Permits diffusion
- Safe to use in contact with drinking water
INGREDIENTS
Standard cements, mineral aggregates, additives, synthetic dispersion powder, sealant
USE
INTRASIT® DS2 54Z is used for waterproofing structures in contact with the soil against ground moisture, non-pressing surface water, seepage water and waste water.
For waterproofing old buildings, cellar walls and structures on the inside surface.
For vertical and horizontal exterior and interior surfaces and for prepared and non-shrinking substrates.
INTRASIT® DS2 54Z is used for waterproofing structures in contact with the soil against ground moisture, non-pressing surface water, seepage water and waste water.
For waterproofing old buildings, cellar walls and structures on the inside surface.
For vertical and horizontal exterior and interior surfaces and for prepared and non-shrinking substrates.
Areas of application:
- Outdoors and indoors
- Washrooms, bathrooms, showers, etc.
- Silos, waster water treatment plants, shafts
- Monolithic water tanks, drinking water containers and swimming pools not deeper than 5 m depth of water
PREPARATION OF THE SURFACE
The substrates must be firm, even, resilient, free of frost, dust, dirt and plaster.
Pre-wet absorbent bases well, so that no moisture is leached from the sealing slurry. The surfaces to be sealed must be free of cracks; if necessary, chisel out cracks and fill with cement mortar or inject resin. Make good any faults, render over rock pockets. Repoint mortar in brickwork, if required. On irregular brickwork with numerous bumps and hollows, apply a leveling coat of cement mortar.
Break all edges under 45° or bevel (bevel width ≥ 3 cm).
Round out all corners with coving of at least 4 cm.
In the case of critical wall and floor slab sealings outdoors and indoors, e.g. when the reverse side is damp, apply a pre-treatment with INTRASIT® VK 10A.
APPLICATION
Guidelines are DIN 1053 for masonry and DIN V 18550 for plaster.
IMPORTANT NOTES
SAFETY PROVISIONS/RECOMMENDATIONS
Contains cement and will cause alkaline reactions when it comes into contact with moisture or water.
Information regarding the safety during transport, storage and handling are included in the updated safety data sheet.
DISPOSAL
The local waste removal regulations must be observed.
The substrates must be firm, even, resilient, free of frost, dust, dirt and plaster.
Pre-wet absorbent bases well, so that no moisture is leached from the sealing slurry. The surfaces to be sealed must be free of cracks; if necessary, chisel out cracks and fill with cement mortar or inject resin. Make good any faults, render over rock pockets. Repoint mortar in brickwork, if required. On irregular brickwork with numerous bumps and hollows, apply a leveling coat of cement mortar.
Break all edges under 45° or bevel (bevel width ≥ 3 cm).
Round out all corners with coving of at least 4 cm.
In the case of critical wall and floor slab sealings outdoors and indoors, e.g. when the reverse side is damp, apply a pre-treatment with INTRASIT® VK 10A.
APPLICATION
Guidelines are DIN 1053 for masonry and DIN V 18550 for plaster.
| 1. | Slowly pour INTRASIT® DS2 54Z into clear water in a clean mixing container while stirring it well until you have a smooth texture without any lumps. Recommended mixing ratio for troweling or brushing: 25 kg INTRASIT® DS2 54Z : 4.5 to 6 litres of water | |
| 2. | Brush the slurry on with a wide brush in at least 2 sessions. Apply the first coat thickly, covering the substrate fully within two hours. Apply the second coat after about 6 hours. | |
| 3. | Clean all processing equipment with water immediately after use. Hardened material can only be removed mechanically. |
IMPORTANT NOTES
- Observe the working temperature of +5 °C to +30 °C.
- Do not mix with other building materials.
- Do not overcoat with materials containing gypsum.
- Check the sealing for minimum layer thickness and any faults before completing work.
- Protect against extreme weathering during the hardening phase.
- Maximum quantity to apply per coat 4 kg/m2.
SAFETY PROVISIONS/RECOMMENDATIONS
Contains cement and will cause alkaline reactions when it comes into contact with moisture or water.
Information regarding the safety during transport, storage and handling are included in the updated safety data sheet.
DISPOSAL
The local waste removal regulations must be observed.
SPECIFICATIONS
| Packaging Container size Delivery form Colour shade Powder density Application temperature Processing time Rain resistant Treadable Coatable Water vapour diffusion resistance factor µ Water imperviousness after 28 days of submersion Bending tensile strength after 28 days Compressive strength after 28 days Adhesive tensile strength Storage | Paper bag 25 kg 40 sacks/pallet grey approx. 1.4 kg/l +5 °C to +30 °C approx. 45 minutes after approx. 4 hours after approx. 8 hours after approx. 7 days approx. 97 approx. 1.5 bar approx. 6 N/mm2 approx. 40 N/mm2 approx. 1.5 N/mm2 dry, 12 months |
Produkty systemowe
INTRASIT® VK 10A
Roztwór krzemianujący przeciw wilgoci wstępującej w murze i betonie