CHARACTERISTICSINTRASIT
® Poly-C1 54Z is a pasty sealant based on polymer-cement with a good adhesion. After mixing the two components together, it becomes a PCC mortar suitable for spreading. For a brushable consistency, add 1 % of water. INTRASIT
® Poly-C1 54Z hardens completely and without stress even in layer thicknesses of 5 mm.
- Crack-bridging
- Impervious to water
- Flexible at low temperatures
- resistant to frost and de-icing salt
- Universal in use
- Can be plastered over
INGREDIENTSLiquid component: polymer dispersion, additives
Powder: special cements, mineral aggregates, additives
USEINTRASIT
® Poly-C1 54Z for waterproofing above and below ground on concrete, plaster and brickwork, for alternative sealing below tiling indoors and outdoors. For horizontal sealing under rising walls. As intermediate and spray water sealing as well as adhesion bridge. When completely sealing concrete surfaces, also in the area in contact with soil and as cellar waterproofing to DIN 18533 W1-E, W4-E. For waterproofing plinths and glueing perimeter insulation boards in the area of splash water. INTRASIT
® Poly-C1 54Z is resistant against the aggressive substances usually found in the soil. Due to its good UV-resistance, INTRASIT
® Poly-C1 54Z can also be used as carbonation brake with concrete components freely exposed to the weather.
Areas of application:
- Concrete, plaster/rendering, masonry
- Damp or wet conditions (washrooms, showers, etc.)
- Balconies, terraces, patios, covered walks
- Sealing of concrete surfaces in contact with the soil
PREPARATION OF THE SURFACESubstrates must be firm, planar, stable and free of oil, grease, frost, dust, dirt, residual mortar and loose debris or particles.
Dry substrates must be pre-wetted to give a matt appearance. Masonry must be fully pointed. Angle off edges and corners, apply hollows.
Small depressions can be smoothed out with a scratch coating of INTRASIT
® Poly-C1 54Z.
Brush or spray on VESTEROL
® TG 10D as a primer for gypsum plaster and plasterboards (gypsum wallboards).
Apply IMBERAL
® Aquarol 10D as a primer on all absorbent, mineral substrates.
APPLICATIONGuidelines are DIN 18533 for waterproofing of buildings and DIN 1053 for masonry.
| 1. | Stir INTRASIT® Poly-C1 54Z using a slow-running agitator (revolving at 400 to 600 rpm).
Stirring time is about 2 - 3 minutes. The powder is stirred into the liquid component. |
| 2. | For a slurry-like consistency: add approx. 0,2 l of water (1%) to the ready-mixed sealing slurry while stirring it well. |
| 3. | INTRASIT® Poly C1 54Z can be applied with a brush, trowel or float, or sprayed. Be sure to apply the sealing compound evenly. Avoid trowel marks in the material surface. |
| 4. | The maximum layer thickness that can be applied per coating session is 5 mm. |
| 5. | To achieve a homogenous, uniform sealing layer without pores, it is recommended to apply the sealing slurry in two sessions. |
| 6. | Drying time of 3 - 5 hours between the coating sessions, depending on the weather conditions. |
| 7. | Clean tools with clean water immediately after use. |
IMPORTANT NOTES- Observe a working temperature of +5° C to +30 °C.
- If the product is applied in direct sunlight, at elevated temperatures and windy weather, early skin formation must be expected.
- For use on dry or nearly dry substrates only.
- Avoid deep trowel marks in the surface.
SAFETY PROVISIONS/RECOMMENDATIONSPowder component contains cement and will cause alkaline reactions when it comes into contact with moisture or water. For detailed information regarding safety during transport, storage and handling, refer to the updated safety data sheet.
DISPOSALThe local waste removal regulations must be observed.
SPECIFICATIONSPresentation
Liquid component
Powder
Delivery quantity
Color
Density, mixed
Working temperature
Workable time
Cold brittle (25 mm spike)
Elongation at tear
Max. tensile strength
Adhesive tensile strength on concrete
Dry
Damp
After freeze-thaw cycling
Imperviousness
Rain-proof 1)
Fully hardened and
load-bearing 1)
VOC-concentration
water damp diffusion
Storage | paper bag /
PE container
5 kg
15 kg
40 bags / 40 containers per pallet
grey
1.70 kg/l
+5 °C to +30 °C
1.5 - 2.0 hours
< 0 °C
approx. 80 %
approx.
1.10 N/mm2
0.8 N/mm2
0.9 N/mm2
0.7 N/mm2
3 bar / 28 days
after about 3 hours
after about
24 hours
< 0,01 %
approx. 1800
frost-free and dry, 12 months |